Can
, ,

FR-830 PCB Underboard Heater

SKU: HFR830

Hakko

  • Compact pre-heater best suited for heat processing on localized areas
  • Featuring quick heatup and less variations in temperature
  • Best suited for pre-heating of multi-layer PWBs

Features

Compact pre-heater with quick start-up and excellent heat recovery.
Combined with HAKKO FR803B(SMD Rework Station)
Easy attachment with connecting cord which is included in HAKKO FR803B
Upgraded working efficiency by heating parts from top and bottom
Operating FR820 with buttons of HAKKO FR803B
(Start Ventilating/Cooling Down by pressing “HOT AIR” button on Handpiece of FR803B)
Automatically cool down after turning off the power
Temperature regulating function
Temperature range 150-300°C(302-572°F)
CAL enables fine adjustment of temperature.
Preheating in short time
The improved air outlet shorten preheat time compared with air conventional product.
Graph
* Please refer to above values, which vary depending on soldering condition.
Hot air temperature 300°C
A gap between the hot air outlet and the PWB for 10mm
Attach sensors to top/under sides of P.W.B and measure temperature.
Suitable for multi-layer board preheating
Automatic cool-down function mounted.
Pushing the “START/STOP” button at the end of work automatically activates the cool-down function.
The FR830-13 PCB Underboard Heater has a compact, lightweight, and slightly larger hot air outlet.
Outer dimensions of HAKKO FR-830
Various types of optional functions
Local heating enabled.
A set of [Extension pipe w/ Lid] is available.
Various types of switching!
[Hand switch][Foot switch] can be connected.

 

Using the optional equipments

 

HAKKO FR-830HAKKO FR830-13 PCB Underboard Heater
+ Omnivise C1390C (2 used) (Rework system) +Extension pipe/with backflow prevention lid B3263 (option)

Extension pipe:Used for localized heating
Backflow prevention lid:When using in combination with SMD rework hot air, use the lid so hot air does not flow back into the FR-830 hot air outlet.

 

Note
Always use the backflow prevention lid when the FR830 switch is off.

 

Set example

 

SMD-BGAHAKKO FR830-13 PCB Underboard Heater
+ SMD rework station HAKKO FR803B (discontinued)
+ Rework fixture C1392B*
+ Omnivise C1390C* (2 used)
*Rework system

 

Various types of switching!
[Hand switch][Foot switch] can be connected.

 

Hand switchConnection cord length: Approximately 100 cm
Switch size: Approx. 30mm (W) / 40mm (D) / 20mm (H)

When using the hand switch, switching is not possible on the main device.

Foot switchConnection cord length: Approximately 135 cm

When using the foot switch, switching is not possible on the main device.

Controlling the temperatures of Hot Air Rework System and workpiece using the Temperature Probe
Measure temperatures of Hot Air Rework System and workpiece using the Temperature Probe for Hot Air Rework System (No. C1541) and thermometer (HAKKO FG-100/HAKKO FG-101) to protect the workpiece.
Controlling the temperatures of Hot Air Rework System
Measuring example

 

* Please refer to above values, which vary depending on soldering condition.
Measuring condition
Hot air temperature 300°C
A gap between the hot air outlet and the PWB for 10mm
Attach sensors to top/under sides of P.W.B and measure temperature.

Usage/Applications

Please keep a gap between the hot air outlet and the PWB for more than10mmto allow the air to flow. When there is not enough space for the air to flow, the fuse may blow up.
Please keep a gap between the hot air outlet and the PWB for more than 5mm to allow the air to flow. When there is not enough space for the air to flow, the fuse may blow up.
 


How to use

When should the optional Temperature Probe for Hot Air Rework System(No. C1541) be used
The Temperature Probe for Hot Air Rework System (No. C1541) is equipped with 2 types of sensors. Before measuring temperatures as follows, connect the sensor to the thermometer.
Sensor A:When measuring the temperature of hot air blown from the nozzle:
Correcting thermal control can be made by confirming the temperature of the hot air that is actually blown.
Sensor B:When measuring the temperature of applicable parts (workpieces):
Rework can be performed without causing damage to the parts being reworked (QFP, etc.)

Packing List

Model No.Packing List
FR-830HAKKO FR-830, Power cord, Instruction manual

Specifications

Model No.FR-830
Power consumption210W (100V), 240W (110V), 470W (120V), 230W (220V), 250W (230V), 270W (240V)
Air flow0.15m3/min. (fan capability)
Temperature range150 to 300ºC (Above the blow exit)
Dimensions140(W)×75(H)×185(D)mm
Weight0.75kg

* Weight (w/o cord)
* Height(H) is the distance from bottom of the feet to the top of the hot air outlet.

Part No.NameSpecifications
photo:B3215B2852Power Switch

Option

Part No.NameSpecifications
photo:B3263B3263Extension pipewith lid
photo:B2763B2763Hand switch
photo:B1649B1649Foot switch
photo:C1391BC1391BNozzle tray
photo:C1392BC1392BRework fixture
photo:C1390CC1390COmnivise

Henchman Products

8 Pavillion Place
Cardiff 2285
New South Wales
Australia

Tel: +61 2 4956 7111
Fax: +61 2 4956 7811

Email Distributor

Visit website

Mektronics Aust Pty Ltd -(Head Office) Seven Hills

5 Prince William Drive
Seven Hills
NSW 2147
New South Wales
Australia

Tel:+61 1300 788 701

Email Distributor

Visit website

Oritech

33 Production Drive
Alfredton 3350
Victoria
Australia

Tel:+61 3 5338 3444
Fax: +61 3 5334 2322

Email Distributor

Visit website

RMS Components Pty Ltd

174B Wecker Road
Mansfield 4122
Queensland
Australia

Tel: +61 7 3390 3302
Fax: +61 7 33903329

Email Distributor

Visit website

WES COMPONENTS

84-90 Parramatta Road
Summer Hill
NSW, 2130
New South Wales
Australia

Tel:+61 2 9797 9866
Fax: +61 2 9798 0017

Email Distributor

Visit website

Westec Distribution Pty Ltd

146 Balcatta Road
Balcatta 6021
Western Australia
Australia

Tel:+61 8 9240 2233
Fax: +61 8 9240 2077

Email Distributor

Visit website

You may also like…